BEMATEC MP-4000 TH DRIVER

Tab ‘Configuration’ At software initialization it will be necessary to configure it before use; this must be the first screen to be accessed before other tabs are used to test the printer functions. Replace the control board to address the issue. Don’t have an account? Removing the Cover Lever Set To remove the lever set it is recommended that the printer cover is also removed. Removing the Cutter Mechanism, Print Head and Connection Board To access the printer interior, the cutter mechanism, thermal print head connection board, follow the steps below: MP TH printer test phases.

Uploader: Mazuzilkree
Date Added: 15 September 2008
File Size: 13.84 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 19915
Price: Free* [*Free Regsitration Required]

When selected the option ‘Formatted text’, the fields ‘Print type’ and ‘Format types’, will be enabled, use the text format styles to test your MP TH printer and get to know the print modes it can perform.

Exploded View Of The Cover Mp-4000 Set The following part numbers are not necessarily available as stand alone units, as they are part of a replacement kit.

Verify if the connection board sensor is properly placed and if there is any dirt obstructing beatec. The recognition of the interface connected to the control board is done with the reading of a code associated to each kind of board through U1, enabled by the SELDEV signal generated by the control board.

Click on the button ‘Get log’ to get a complete report on the printer configuration. You can change the time the buzzer will be on and the time it will be off. The recognition of the interface connected to the control board is done with the reading of a code associated to each kind of board through U2, enabled by the SELDEV signal generated by the control board.

  AIRPCAP 2.0 DRIVER DOWNLOAD

The correct position to connect this cable is on the CN4 connector as shown on the image on the side. Tab ‘Configuration’ At software initialization it will be necessary to configure it before use; this must be the first screen to be accessed before other tabs are used to test the printer functions.

Bematech MP-4000 TH Programmer’s Manual User Manual

Red LED blinking 8 times – Print Mechanism Error On the print initialization, the status of the print head and the paper feed motor picture below are verified. To remove the control board set, simply pull the cartridge back and then out. By pressing ‘print’ button you will print only current page. Page 27 To remove the control board set, simply pull the cartridge back and then out. Page 30 To separate the connection board from the cutter mechanism, start by loosening the screw that holds the grounding cable located on the side of the equipment, then move away the connection board and disconnect the cables.

Begin disassembly by removing the control board cartridge, according to the previous topic. Page 47 There is a sensor on the right side of the printer picture above that notifies it when the cover is closed.

Bematech Mp Th Fi SM SP Thermal POS Receipt USB Printer | eBay

After disconnecting the plastic chassis, just pull up the back side to loosen the frontal part. On this field it is possible to make some changes in the bar code that will be printed. Who should read this manual? beamtec

  655 AC97 AUDIO DRIVER DOWNLOAD

Page 4 Chapter Tab ‘macro Tab ‘Macro’ The tab ‘Macro’ allows tests to be processed in batch mode. Tab ‘Additional Commands’ 1. Tab ‘Macro’ The tab ‘Macro’ allows tests to be processed in batch mode.

Hier entsteht was Neues für Sie!

The product firmware update can be performed by using the ‘User’s Software’ or the ‘Technical Support Software’. Introduction Introduction This manual provides information on the identification and troubleshooting, test procedures and a list of replacement parts for the MP TH printer. The option Bitmap allows you to check the graphics printing and the Logo option allows you to test the functions of logo storage and logo printing from volatile and non volatile memories.

Page 48 – Verify if the mechanism plastic chassis pins where the sensor is connected image on the side are not broken, which would let the sensor out of its position, leading to its malfunction.

Below you can see the cutter mechanism, the print head and the connection board with mp-000 thermal print head connection cable. How this manual is organized Chapter 1 Knowing the product.

Bematech MP User Manual 36 pages. To print the manual completely, please, download it.

Notice the correct way to insert the sensor on the Tab ‘status Tab ‘Status’ 1. Enter text from picture: Accessories 1 Please contact Bematech to consult the availability of the interfaces and accessories.